Pneumatic valve is the role of the worm gear box drive and operation

on both sides of the worm gear box of worm bearing is different, one side is a single deep groove ball bearings, thrust bearings to install relative to one another, on the other side is a cone as power input terminal of the good that, please. The power input should be set at one end ball bearing, is also the scale free end of the shaft, The end is equipped with coupling, a displacement space.

cone thrust bearing is a fixed end. Worm gear and worm reducer center distance small solution is definitely a mistake oh, can repair welding first, then the new boring, such as materials, the best from the new one. Change of worm worm gear is not reality, system into the absolute worth than the body.
。 The new boring, in another type of bearing ( The inner hole is changeless, outer diameter increases.
。 Set set. Can repair welding first, then the new boring!

worm gear box drive the operation of the pneumatic valve
worm gear box the use of pneumatic valve, pneumatic valve worm gear box when it should be noted that the open-close direction of the operation, it shall be clockwise closing, in the opening and closing operation side should be square tenon, standard and size, and face to the ground, so that people can be directly from the ground. Pneumatic valve closing worm gear box of the dial needle material under the condition of management better available stainless steel plate, or paint for steel plate, do not use the aluminum skin production; And striking, fixation. Increasing the service efficiency of regulating pneumatic valve and time.

how to make the maximum efficiency of worm gear box pneumatic valve, pneumatic valve will be according to closing pressure, the calculation of unbalanced force, in order to determine the structure size of pneumatic valves and actuators, close to first, to ensure that adequate power output. To determine the optimal flow rate at the same time, in order to seal.
when use pneumatic valve worm gear box mechanical products should pay attention to how to correct and safe operation, on the basis of this raise the use efficiency of products, this is we all hope to achieve when using any mechanical products efficiently.

function and fault analysis of turbine box:
the turbine system is one of the most common pressurization system of turbo engine.
if the unit is in the same time, to be able to put more air and fuel mixture forced into the cylinder ( The combustion chamber is compressed and explosion action ( Small displacement engine to 'breathe' and large displacement of the same air, improve the efficiency of volume, nature can be under the same speed to produce the engine air intake greater power output. Turbocharged using exhaust gas drive, basic no additional energy loss ( No additional burden on an engine, can easily create muscle, is a very smart design. Situation as you get a fan to blow into the cylinder, forced the wind to fill, make the air quantity increase, in order to get larger horsepower, just this fan is not using an electric motor, but with the exhaust gases from the engine to drive.
in general, the engine in cooperate with such a 'forced air intake' action, can raise % - at least % of the extra power, such an astonishing effect is the reason why the turbocharger cuddly. Besides, the perfect combustion efficiency and power to a huge rally, was originally a turbocharging system can provide the vehicle's largest value.

the system includes the turbocharger, inter-cooled, beside the inlet and vent valve, next to the exhaust ventilation valve and the inlet and exhaust pipes of form a complete set.

turbine box in use process will appear some fault, we will be part of the main fault listed below:
. Because of the small oil cylinder polyurethane sealing ring is damaged, pressure oil into the worm gear box of worm gear box at the top of the lubrication of pressure oil emitted or display of worm gear box oil lubricating oil height has increased significantly.
。 Due to putting on the pin fracture and unable to drive the clutch plate led to the auxiliary pump output pressure oil measured can meet the requirements, but not with a knife or cutting paper.
。 Double vane pump itself quality problems caused by the noise and the pulley bearing oil shortage or damage to machine vision during idle running.
。 The skeleton oil seal on the top of the double vane pump shaft damage line often appear in the air.
。 In the process of cutting a small regular phenomena of the knife.