lv-pneumatic
Pneumatic industry,Diaphragm Valves of Bag House Filter, Personalized Customization
Latest products
What about CFR/CNF of pneumatic manual valves ?
2019-07-01
AIRWOLF CO, LTD is committed to producing quality pneumatic manual valves and providing comprehensive and reasonable solutions for customers. AIRWOLF's hydraulic valve is widely used in multiple industries and fields. Consulting and order from friends of all walks of life are welcomed! We sincerely look forward to your consulting and purchase! The diaphragm kit series has many styles to meet the diversified needs of customers.
What about the oil mist of the gas source binary oil-water separator? Why is there often water in the three-part (gas source processor?These water is the steam in the air. when the air is compressed and pushed into the pipeline by the air compressor, without the full moisture and filtration, the water vapor is easy to condense in the pipeline. If you have requirements for air quality, you should install dryers, filters, etc.When the air enters the gas source processor, the gas source will effectively intercept the water vapor after passing through the filter. if the filter filtering effect is not good, the water vapor will enter the solenoid valve/cylinder/equipment, causing the rear section to be abnormal, affects service life and performance. The filtering effect is good, and the water will be stored in the filter cup. at this time, there are four emission modes of hand row, self row, semi-automatic and hand row in the filter, please select the appropriate model according to the operating environment and
About dust removal equipment Cyclone dust collector is the centrifugal force generated by rotating dust-containing gas,A dry gas that separates dust from the air flow-Solid separation device.When the dust-containing air flow enters the cyclone dust collector from the intake pipe,The airflow will change from linear motion to circular motion.The dust particles with a density greater than the gas contact the wall and lose the inertia force and fall along the wall,Enter the ash discharge pipe.When the spin-down external air flow reaches the cone,Close to the center of the dust collector due to conical shrinkage.When the airflow reaches a certain position at the lower end of the cone,That is, from the middle of the cyclone dust collector in the same direction of rotation,Continue to do spiral flow from bottom to top.Finally, the purified gas is discharged from the exhaust pipe.Some of the dust particles that were not captured also escaped.For capture, separation 5-The dust efficiency above 10 μm is h
What about the oil mist of the gas source binary oil-water separator? Why is there often water in the three-part (gas source processor?These water is the steam in the air. when the air is compressed and pushed into the pipeline by the air compressor, without the full moisture and filtration, the water vapor is easy to condense in the pipeline. If you have requirements for air quality, you should install dryers, filters, etc.When the air enters the gas source processor, the gas source will effectively intercept the water vapor after passing through the filter. if the filter filtering effect is not good, the water vapor will enter the solenoid valve/cylinder/equipment, causing the rear section to be abnormal, affects service life and performance. The filtering effect is good, and the water will be stored in the filter cup. at this time, there are four emission modes of hand row, self row, semi-automatic and hand row in the filter, please select the appropriate model according to the operating environment and
About dust removal equipment Cyclone dust collector is the centrifugal force generated by rotating dust-containing gas,A dry gas that separates dust from the air flow-Solid separation device.When the dust-containing air flow enters the cyclone dust collector from the intake pipe,The airflow will change from linear motion to circular motion.The dust particles with a density greater than the gas contact the wall and lose the inertia force and fall along the wall,Enter the ash discharge pipe.When the spin-down external air flow reaches the cone,Close to the center of the dust collector due to conical shrinkage.When the airflow reaches a certain position at the lower end of the cone,That is, from the middle of the cyclone dust collector in the same direction of rotation,Continue to do spiral flow from bottom to top.Finally, the purified gas is discharged from the exhaust pipe.Some of the dust particles that were not captured also escaped.For capture, separation 5-The dust efficiency above 10 μm is h
Custom message
