Ceramic pneumatic valve installation and maintenance instructions _ pneumatic components factory valve industry

Pneumatic pneumatic valve ceramic valve is a valve pneumatic components factory owners to produce one of the valve, because ceramic pneumatic valve has corrosion resistance, wear resistance, cavitation resistance and other advantages, favored by the majority of customers trust and support; When installing a ceramic pneumatic valve, customer need the correct installation on the pipeline, to avoid the installation error, affect the operation of ceramic pneumatic valve service life, the detailed introduction ceramic pneumatic valve installation and maintenance instructions, for customer for reference. 1, determine the service life of the ceramic pneumatic valve installation length is the key point is the ceramic pneumatic valve installation. Improperly installed make ceramic pneumatic valve performance is reduced the possibility is very large, such as the proper attention during the installation process will improve the reliability of ceramic pneumatic valve operation. 2, in the pneumatic valve installation before confirm ceramic pneumatic valve is in good working condition is very important, the commonly used several of the following requirements to avoid ceramic pneumatic valve follow-up question is helpful: 1. Carefully remove ceramic pneumatic valve protection items, contrast material labels and signs. (2) must pay attention to attached to the ceramic pneumatic valve or along with professional warning labels, and take the appropriate measures. (3) check the ceramic pneumatic valve flow marks, such as flow, should be in accordance with the flow, in accordance with the ceramic pneumatic valve. (4) when installation should be clean inside cavity and sealing surface, check whether the packing is pressure, whether connecting bolts evenly on tight. (5) ceramic pneumatic valve should be installed according to allow working position, but must pay attention to maintenance and operation is convenient. 6. Rotate handwheel when opening or closing, unfavorable and with the aid of other auxiliary leverage; 7 if possible - through ceramic pneumatic valve, operators to fully open Close - Open loop operation inspection ceramic pneumatic valve performance is normal. Pay attention to in the operation of the ceramic pneumatic valve to avoid damage. Today in the ceramic pneumatic valve before installation, check whether connected with ceramic pneumatic valve pipe positioning correctly, clean and no ducts, foreign body. Pet-name ruby installed should be regular maintenance, clean up dirt of lumen, check the sealing surface, abrasion of stem nut. Ceramic pneumatic valve note: 1, unless you need to check and install ceramic pneumatic valve, suggested that do not remove ceramic pneumatic valve protection cover. 2, if ceramic pneumatic valve must be on the outside, the ceramic pneumatic valve support should be up to no contact with the ground or the road, to be protected and use waterproof cover. 3, ceramic pneumatic valve shall be installed in the pipeline before positioning in general. Piping to nature, the wrong position can't hard pull, lest leave prestressed. 4, when tighten the clamping screw, ceramic pneumatic valve should be in open state, so as not to crush the valve sealing surface. After 5, all ceramic pneumatic valve in place, should make an opening and closing, flexible no jam phenomenon for qualified. 6, it is strictly prohibited in the installation of the valve stem when climbing scaffold. 7 and above 200 ℃ high temperature ceramic pneumatic valve, due to the installation time at high temperature, the normal use, temperature, expansion bolt is heated, clearance increase, so must tighten again, is called a 'hot', operators should pay attention to this work, otherwise easy to leak. 8, when the weather is cold, and the water valve closed parked for a long time, should be ruled out the valve water. After steam stop valve, also want to eliminate the condensate. Bottom of the valve is a plug, it can be open drainage. 9, ceramic pneumatic valve operation, opening and closing force cannot too big, cannot make MengJin especially. Also note to avoid ceramic end knock against. 10, the new pneumatic valve when using ceramic, padding don't press too hard, don't leak as degrees, lest stem pressure is too big, to speed up the wear and tear, and opening and closing. 11, ceramic pneumatic valve to keep for a long time in a position to be not moved, the operational may fall to some extent, this is because the valve spindle lose effective lubrication, packing aging, corrosion or pests accumulation caused by running parts. If there is such occasions of * good custom this cyclical part or all of the ceramic pneumatic valve cycle operation plan. Pneumatic components factory specializing in the production of ceramic pneumatic valve industry valve manufacturers, customers in the selection, need according to the using environment and temperature, to choose ceramic pneumatic valve body materials, nominal pressure, using the related technical parameters, such as temperature, nominal size, and whether driving mode choice worm gear, pneumatic actuator, electric valve actuators, so that our sales staff for selection and quotation. : stationary ceramics working principle of the pneumatic valve Q941TC electric ceramic pneumatic valve sealing butterfly valve _ _ wear-resisting ceramics high temperature ceramic butterfly valve butterfly valve